How to Draw 30 Degree Angle in Autocad TUTORIAL

1. Click Dwelling house tab > Draw panel > Line . Notice
2. Specify the start point and stop point of the line segment past clicking in the cartoon area.
3. Go on specifying additional line segments.

   To disengage the previous line segment, enter u at the prompt. Click Undo on the Quick Access toolbar to cancel the entire series of line segments:

   

4. Press Enter or Esc when done or enter c to close a series of line segments.

Using Specific Coordinates

1. Click Abode tab > Draw panel > Line . Find
2. Blazon the coordinate value for the start point by typing the X value, a comma, then the Y value, for example 1.65,four.25.
3. Press the Spacebar or Enter.
4. Do i of the following:
   • If dynamic input is on: Type the pound sign (#) followed by the 10-value, a comma, then the Y-value, for example #4.0,6.75.
   • If dynamic input is off: Type the X value, a comma, then the Y value, for example 4.0,vi.75.
5. Press the Spacebar or Enter.

Notation: When dynamic input is on, relative coordinates are the default. When dynamic input is off, absolute coordinates are the default. Press F12 to plough dynamic input on or off.

Using a Relative Coordinate

1. Click Domicile tab > Draw console > Line . Observe
2. Specify the outset indicate.
3. To specify the 2d signal relative to the first betoken, do one of the post-obit:
   • If dynamic input is on: Type the 10-value, a comma, and so the Y-value, for case iv.0,six.75.
   • If dynamic input is off: Blazon the at sign (@) followed by the X-value, a comma, then the Y-value, for example @4.0,6.75.
4. Press the Spacebar or Enter.

A Specific Length

1. Click Home tab > Depict panel > Line . Find
2. Specify the kickoff bespeak.
3. Do one of the following to specify the length:
   • Move the cursor to indicate the management and angle, and enter the length, for example 6.5.
   • Enter the at symbol (@) and the length, followed past the left angle bracket (<) and the bending, for example @half dozen.5<45.
4. Press the Spacebar or Enter.

At a Specific Bending

1. Click Home tab > Draw panel > Line . Find
2. Specify the start signal.
3. Do one of the post-obit to specify the angle:
   • Enter the left angle bracket (<) and the bending, for example <45, and motion the cursor to indicate the management.
   • Enter polar coordinates, for example 2.5<45.
   • Press F8 to plow on Ortho to lock the angle to horizontal and vertical directions. You can also press Shift when specifying the next bespeak for a horizontal or vertical direction.
   • Press F10 to turn on polar tracking. You might demand to apply the DSETTINGS command, Polar Tracking tab to specify additional polar angles and choose the option to track all polar bending settings.
   • Movement the cursor to bespeak an judge angle.
4. Exercise i of the following to specify the length:
   • Click a point to specify the endpoint with or without using object snaps. Trim or extend the resulting line as needed.
   • Enter the length of the line, for instance 2.five.
5. Press the Spacebar or Enter.

At a Specific Bending to Another Line

Temporarily aligning the UCS icon with an existing line makes it piece of cake to describe a line at a specific angle to some other line.

1. At the control prompt, enter UCS.
2. Enter ob for Object and select the existing line.

   The UCS origin (0,0,0) is redefined.

   

3. Click Home tab > Describe panel > Line . Find
4. Specify the starting time point.
5. Do one of the following to specify the angle:
   • Enter the left angle bracket (<) and the angle, for example <45, and move the cursor to indicate the management.
   • Motility the cursor to indicate the approximate bending.
6. Specify the second point.
7. Press the Spacebar or Enter.
8. At the command prompt, enter UCS.
9. Enter p for Previous to reset the UCS origin.

DOWNLOAD HERE

How to Draw 30 Degree Angle in Autocad TUTORIAL

Posted by: patriciawhostravion1997.blogspot.com